The gauge on a domestic gas meter set is a small instrument bought in very large numbers. We manufacture it in Faridabad, to your specification, at CGD volumes.
India's city gas distribution networks are being built out faster than almost any other utility infrastructure in the country. Every household connection that goes in carries a service regulator, a meter set and, on most designs, at least one pressure gauge.
That is a small instrument in a very large number. A single CGD company covering a geographical area adds connections continuously, and every one is an identical assembly repeated thousands of times. The gauge is not a specification challenge; it is a supply and consistency challenge.
That distinction matters, because it is a completely different purchasing relationship from the industrial work on the rest of this site. A refinery buys one gauge and asks fifty questions about it. A CGD company settles the specification once and then needs the same gauge, identical, in batches, on schedule, for years.
We build for both, and we do not confuse the two. This page is about the second.
Batch-to-batch identity. Ten thousand gauges that are individually acceptable but visibly different from each other create a field problem — installers question them, inspectors question them, and consumers notice. Consistency across a batch matters more than any single unit specification.
A schedule that is actually held. A connection programme runs to targets. A gauge shortage stops commissioning at the last step of an assembly that took weeks to reach. We would rather quote a realistic date than an optimistic one you plan around.
The correct range for the network, not a catalogue range. Service and distribution pressures differ between networks and between design stages. A gauge ranged for the wrong part of the system reads at the bottom of the dial and is functionally useless to a technician.
Documentation that scales. Batch test certificates and calibration traceability that can be produced per lot rather than per piece, because a certificate per gauge on a ten-thousand-unit order is not a system that works.
An outdoor life. A meter set gauge sits outside a house for years — sun, monsoon, dust, and occasionally a wash. Case sealing and dial legibility after three summers are the real specification.
The visible gauge on a household connection, ranged for service pressure so a technician can read it at a glance from a standing position.
Inlet and outlet gauges that verify the regulator is doing its job — the most common diagnostic point on a domestic complaint call.
Larger assemblies for restaurants, hotels, hospitals and factories drawing from the same network at higher offtake.
Where the requirement moves closer to conventional industrial practice, and where the rest of this site becomes relevant.
Domestic meter set assembly. The visible gauge on a household connection, sized and ranged for service pressure so a technician can read it at a glance from a standing position.
Service regulator inlet and outlet. Verifying the regulator is doing its job, which is the single most common diagnostic point on a domestic complaint call.
Commercial and industrial connections. Larger assemblies for restaurants, hotels, hospitals and factories drawing from the same network at higher offtake and, frequently, different pressure.
Pressure regulating stations and skids. District regulating stations and customer PRS skids, where the instrumentation requirement moves closer to conventional industrial practice.
Distribution main and MDPE network points. Test and monitoring points along the network itself, where the gauge is a maintenance and commissioning tool rather than a permanent consumer-facing fitting.
We manufacture pressure gauges at our works in Faridabad, Haryana. Not assemble imported ones — manufacture, test and calibrate against reference standards held on site. That is the same capability behind the industrial instruments across the rest of this site.
For CGD volumes that capability matters in a specific way: a manufacturer can hold a specification constant across batches because the specification lives in our process, not in whichever supplier had stock that month.
We are also honest about what we are not. We do not manufacture regulators or meters, and we will not pretend to. Where a tender bundles those together, we are the gauge supplier within it and are happy to work alongside whoever supplies the rest.
And we would rather build to your drawing than sell you ours. If you have an existing approved gauge, send us one — dial, case, connection, range and marking — and we will quote to match it rather than asking you to re-approve something new.
Ten thousand individually acceptable gauges that differ visibly from each other create a field problem. Consistency matters more than any single unit.
A gauge shortage stops commissioning at the last step of an assembly that took weeks to reach. We quote realistic dates rather than optimistic ones.
Batch test certificates and traceability that scale. A certificate per gauge on a ten-thousand-unit order is not a working system.
Case sealing and dial legibility after three summers outside a house is the real specification, not the accuracy class.
Building a network or expanding a geographical area? Send the meter set drawing, the service pressure design and your annual connection target. We will propose the gauge specification, tell you where the design is asking for something it does not need, and quote against the volume rather than against a single piece.
Already running and unhappy with consistency? That is the most common reason CGD buyers change gauge supplier. Send us a sample from a recent batch alongside one from an older batch — the difference between them is usually the whole conversation.
Field failures on installed gauges? Tell us what is failing and after how long. Clouded dials, water ingress and pointer drift each point to a different cause, and the fix is a specification change rather than a better brand.
Sample first. For any serious enquiry we will supply samples for your approval and field trial before you commit to a rate contract. On a product bought in these numbers, that is the sensible order of things.
Yes, and it is work suited to us — a small instrument built to a fixed specification in repeat batches. Send the meter set drawing or an existing approved gauge and we will quote to match it.
Usually, and we would prefer to. Send us a physical sample. Dial, case, connection, range and marking can all be matched, which avoids putting you through a fresh approval process for a component that already works.
This is batch supply work rather than one-off. Tell us the annual connection figure and the delivery schedule and we will quote against that, because the price and the plan both depend on it.
It follows your network design rather than a catalogue. A gauge ranged for the wrong part of the system sits at the bottom of the dial and is useless to a technician on a complaint call. Send your service pressure design.
Batch test certificates and calibration traceability per lot. A separate certificate for every gauge on a ten-thousand-unit order is not a system that works in practice, and we would rather propose one that does.
Usually moisture ingress through the case seal or the connection, and it is a specification issue rather than a quality one. Tell us where they are mounted and how long they last, and we will tell you what needs changing.
No, and we will not pretend otherwise. We manufacture the pressure gauges. Where a tender bundles regulators and meters together, we are happy to be the gauge supplier within it and work alongside whoever supplies the rest.
Yes, for any serious enquiry. Samples for approval and field trial before a rate contract is the sensible order of things on a product bought in these numbers.
Send a photograph of the nameplate, a tag list, or simply tell us the duty. Our engineer will size it and quote it.
Talk to an engineer on WhatsAppCall +91 98107 02836Email the specification